# creator5-fw-builder — build configuration
# Edit paths to match your machine, then run `make build`.

# ---- identity of the package you are building -------------------------------
MOD_NAME=anvil                  # goes into the .tgz filename
MOD_VER=""                    # empty = today's UTC date, e.g. 20260823.
                              # Pin it to rebuild an old release, or for a
                              # second release on the same day (20260823b).

# Version stamped on the software component. Empty = keep the stock number
# (recommended). The installer wipes every other version dir before renaming
# its temp dir, so a collision is not a problem; a suffix like 1.9.7-mod is
# only useful if you want to see at a glance that a machine is modded.
SW_VER=""

# ---- which printer is this for? --------------------------------------------
# Creator5Pro / 0029   or   Creator5 / 0028
# Find it on the printer: Settings -> About, or in
# /usr/data/firmwareRes/config/general.json ("machineName").
#
# This MUST match the model the stock package was built for. A package's
# runFirmwareExe.sh carries its own MACHINE=/PID= gate and refuses to install
# on the other model, so a Pro cannot be recovered or modded with a non-Pro
# package (and vice versa).
TARGET_MACHINE=Creator5Pro

# Override for one command:  MODEL=Creator5 make build
# Build both at once:        make release

# ---- inputs (sources you already have on this machine) ----------------------
# Everything below is relative to this. Point it wherever you keep the
# firmware and the source repos; nothing here is committed (config.env is
# gitignored, this file is the template).
DESKTOP="$HOME/Desktop"

# Stock OTA packages, ONE PER MODEL. They are not interchangeable: each
# carries a different firmwareExe and refuses to install on the other model.
# The one matching TARGET_MACHINE (or MODEL=) is selected automatically.
STOCK_TGZ_CREATOR5PRO="$DESKTOP/Creator5-1.9.7-1.2.9-20260810/Creator5Pro-1.9.7-1.2.9-20260810.tgz"
STOCK_TGZ_CREATOR5="$DESKTOP/Creator5-1.9.7-1.2.9-20260810/Creator5-1.9.7-1.2.9-20260810.tgz"

# Set this only to force one specific package regardless of model.
STOCK_TGZ=""

# Your Klipper fork (branch creator5) -- klippy tree + prebuilt MIPS c_helper.so
KLIPPER_FORK="$DESKTOP/klipper"

# The toolchanger mod (klippy-extras + configs + helixscreen db entry) used to
# be a TOOLCHANGE= path to a creator5-toolchange checkout. It now lives in this
# repo under payload/klipper/, so there is nothing to set. BUILD_TOOLCHANGE=0
# here still turns it off.

# Mainsail and the HelixScreen build for the Creator 5 (MIPS static) are NOT
# set here. They are downloaded on demand into vendor/ by bin/fetch-assets.sh,
# pinned by version and sha256 in versions.env, so the repo carries no
# binaries. Set either of these ONLY to build against your own local copy.
# NOTE: the path is still checksummed against versions.env, and on a mismatch
# fetch-assets.sh OVERWRITES it with the pinned release -- SKIP does not save
# you, it re-downloads too. To build against your own file, also put ITS
# sha256 in versions.env; only an exact match is left alone ("cached"):
#HELIX_TGZ="$DESKTOP/helixscreen-creator5-v0.99.115.tar.gz"
#MAINSAIL_ZIP="$DESKTOP/mainsail.zip"

# Optional extras -- leave empty to skip that feature
BUSYBOX_BIN="$DESKTOP/creator5/busybox"          # optional richer busybox

# ---- what the installed image does at boot (baked into anvil.conf) ----------
# RUNTIME switches: they are written into /usr/data/anvil/anvil.conf, which the
# printer re-reads at every boot, so they can be changed over ssh afterwards.
#
# The BUILD_* flags that decide what goes INTO a package (BUILD_KLIPPER,
# BUILD_MAINSAIL, BUILD_MOONRAKER, BUILD_HELIX, BUILD_TOOLCHANGE) are not set
# here: bin/common.sh defaults them to the full firmware, and setting one in
# this file overrides that. Only touch them if you want a piece left out.
MOD_WEB=1                     # 1 = start nginx (Mainsail) + moonraker
MOD_CAM=1                     # 1 = start mjpg-streamer on :8080 (firmwareExe used to)
MOD_UI=1                      # 1 = start HelixScreen on the touchscreen
MOD_SSH=1                     # build-time only: 1 = set a root password.
                              # ssh itself is stock S50dropbear, always up.
MOD_WIFI=1                    # 1 = bring up wlan0 (firmwareExe used to do this)

# ---- root login shipped in the image ---------------------------------------
# This is the whole "enable ssh" feature. The stock rootfs already runs
# dropbear from /etc/init.d/S50dropbear, so port 22 is ALREADY open on a
# stock printer -- there is simply no published root password.
#
# Empty = the INSTALLER picks a random password on the printer and writes it
# to anvil-password.txt on the USB stick you flashed from. Every machine gets
# a different one, which a hash baked into a shared package never could.
# Set one here to choose your own:   openssl passwd -6 'yourpassword'
ROOT_PW_HASH=""

# ---- crypto (from /usr/prog/bin/unTar on the printer) -----------------------
FF_KEY='FFP0331&*%root'

# ---- the printer replica -----------------------------------------------------
# Nothing here. The replica's settings -- the factory image, the partition
# sizes, a prebuilt printer image -- live in test.env, because they exist only
# for the tests and must never reach a printer:
#
#     cp test.env.example test.env