matthewtrahan 85fea24b18 ui: Remove model review fix -- forgetSessionNote's doc comment back above it

2026-10-18 09:23:30 -05:00

..

calibration

calibration: rebuild the cutout coupon's print files with the review fixes -- still no edge on more than two faces, PrusaSlicer time and filament unchanged

2026-10-15 11:42:12 -05:00

fins

islands: review fixes -- the readout's '(+N midair starts)' no longer stacks on every rebuild, removal or Show midair starts toggle (only the line's rewrites append it; builds redraw the card); the red's bare area is read before the island walls, so Full's rows-or-patch pick stays main's; the card says when the island pass ran out of walls, and in Full on a point-seated part with the pad off that none got one

2026-10-18 09:05:08 -05:00

i18n

ui: Remove model -- a button in the stats card takes the part off the plate and brings back the start page, so the next model needs no reload; the drawn walls, removed fins, load arrow, Suggest list, section cut, scale, import note and undo go with it, the fin settings stay

2026-10-18 09:23:30 -05:00

prop

curved walls: review fixes -- a traced group's other regions count as served where its walls reach their own faces (they read bare and drew last-resort walls), and a group's wall within a foot + 1 mm of a wall an earlier group swapped in is dropped (stacked surfaces met 0.15-0.43 mm apart on the bean on its side); the spec names the limits (shallow bands give stubs, one bend swaps a whole group)

2026-10-17 20:33:56 -05:00

ui

ui: Remove model review fix -- forgetSessionNote's doc comment back above it

2026-10-18 09:23:30 -05:00

vendor

picks: every Mesh raycast through three-mesh-bvh (vendored 0.9.15, MIT) -- a Draw hover on a 1.56M-face mini took 75 ms a pointer move, now under 1 ms with the same hits; the BVH builds on a big mesh's first pick

2026-10-14 21:05:50 -05:00

_headers

picks: review fixes -- the vendored BVH is cached a year like occt and manifold, and pick.js's load-cost note stands on its own

2026-10-14 21:05:50 -05:00

_redirects

Make the controls readable and drop the Brace mode

2026-07-30 13:55:26 -05:00

.gitkeep

Initial commit: fin spec, prototype, project skeleton

2026-07-24 19:25:22 -05:00

app.js

ui: Scale -- one uniform percent in the view toolbar beside Rotate; a new scale reloads the part at that size from the part as loaded (never compounded), keeps the pose, scales a 3MF's negative parts and modifiers about the same centre, and clears drawn walls, removed fins and undo as a new file does; the badge reads the percent while it isn't 100

2026-10-17 21:09:43 -05:00

apple-touch-icon.png

site: add fin logo — favicon set + brand mark (generator in assets/)

2026-08-24 19:12:03 -05:00

cut.js

cut: review fixes -- a cutter that will not load leaves the file open uncut with a note (and is retried next file) instead of refusing it, an inside-out negative is turned outward so it cuts rather than adds plastic, the shell/debris repair is for negatives only (the part is never changed without a word), and negatives that remove the whole part leave it uncut with a note

2026-10-14 20:21:26 -05:00

cutout.js

walls: review fixes -- squat walls narrow too (a 1.2 mm squat wall at 8 lines leant 24deg), a cut wall's bands and strips keep to the narrowed body, and the clearance probe reads the body from the same rise the mesh does on a low tail (044)

2026-10-17 13:52:49 -05:00

draw.js

tall ribs: walls over 10 cm get face ribs at the plate (Brace tall walls, on) -- a user: fins taller than 10 cm wobble; Auto, Full and Draw, last around every support, kept sideClear off the part and other supports

2026-10-16 14:31:03 -05:00

exportname.js

export: the file name carries the nozzle and layer height the fins were built for (#279) -- part-fins-0.6nozzle-0.24layer.3mf, so the slicer gets set to match: a 0.4 build sliced at 0.6 prints its walls as one line and drops tines between 0.24 layers

2026-10-15 21:04:59 -05:00

favicon-32.png

site: add fin logo — favicon set + brand mark (generator in assets/)

2026-08-24 19:12:03 -05:00

favicon.svg

site: add fin logo — favicon set + brand mark (generator in assets/)

2026-08-24 19:12:03 -05:00

fins.js

islands: review fixes -- the readout's '(+N midair starts)' no longer stacks on every rebuild, removal or Show midair starts toggle (only the line's rewrites append it; builds redraw the card); the red's bare area is read before the island walls, so Full's rows-or-patch pick stays main's; the card says when the island pass ran out of walls, and in Full on a point-seated part with the pad off that none got one

2026-10-18 09:05:08 -05:00

finworker.js

comments: point prop.js mentions at the web/prop/ module that owns the code

2026-09-26 17:46:36 -05:00

gridsize.js

grids: review fixes -- a pierce found on the fine grid reports the one the old 64x64 walk met first (9% of pierces moved up to 1.5 mm, and callers trim the station nearest it), buildFins drops its seated part when done, gridsize's comment counts cells right

2026-10-14 20:30:08 -05:00

index.html

ui: Remove model -- a button in the stats card takes the part off the plate and brings back the start page, so the next model needs no reload; the drawn walls, removed fins, load arrow, Suggest list, section cut, scale, import note and undo go with it, the fin settings stay

2026-10-18 09:23:30 -05:00

inside.js

grids: review fixes -- a pierce found on the fine grid reports the one the old 64x64 walk met first (9% of pierces moved up to 1.5 mm, and callers trim the station nearest it), buildFins drops its seated part when done, gridsize's comment counts cells right

2026-10-14 20:30:08 -05:00

islands.js

islands: a start touching only amber (a sliver too small for a fin) counts -- a 2 x 2 mm peg end in midair got no fin and only 'may come out rough'; now a cone too (Matthew 2026-10-17). DRO housing: its two 3 mm pin ends under the top show

2026-10-18 09:05:08 -05:00

kiss.js

tines: an end stops at the first solid -- the far probe (2x the reach) passed a part thinner than it and ran the tine through, and bisected back from a piece beyond a thin near one (cone/needle/tube X40: tine corners 0.3-0.5 mm into a thin edge at 0.2 layers); where the walk finds nothing the end is unchanged to the bit

2026-10-14 13:42:33 -05:00

materials.js

engine: sway brace tines kiss the part's face (kissEnds), and the material's tine bite is gone -- one SWAY.tineReach 0.3 gates placement; Material tooltip no longer claims PETG shrinks a bite; same braces and tines on 16 cases x PLA/PETG, slices identical on 30 of 32 (lighthouse Y90 notch: +-0.13 mm2)

2026-10-03 15:14:03 -05:00

nozzle.js

walls: a wall too low for its neck narrows its body instead of squeezing the neck flat -- at 8 wall lines a 1.5 mm wall's shoulder leant 28deg, an overhang on the wall's own side (local issue 044); 2-line walls unchanged (864/864 sweep identical), same walls and tines at 0.4x8 and 1.2x4

2026-10-17 13:52:49 -05:00

obj.js

import: OBJ review fixes -- an inline # comment on a face line read as a vertex ref, a CR-only file's \ continuation wasn't joined, a big file split into millions of line strings (now one scan into growable typed arrays; a file past the string limit says so), and a 3MF's import note outlived the OBJ after it on a language switch

2026-10-16 10:00:56 -05:00

orient.js

refactor: decouple orient.js from UI i18n and deduplicate translation key (#222)

2026-10-09 17:58:14 -05:00

overhangs.js

islands: find island starts -- a mesh low point (a vertex, or a level edge) whose faces point down, none red, joining nothing lower within a layer and with nothing within 0.3 mm in the layer below, cross-section >= 0.03 mm2 a layer up; starts within 2 mm merge (041). Not used yet. #18 at X45: 16 islands; #257's corners found; 0 on the scanned and mini parts, under 35 ms

2026-10-18 09:05:08 -05:00

pieces.js

engine: floatingPieces moves to web/pieces.js; plainer readout line

2026-09-27 13:48:23 -05:00

planes.js

comments: say the leaning-fin code they cite is gone

2026-09-27 07:58:51 -05:00

prop.js

curved walls: on a jagged overhang the curves trace each region grown across the slivers around it (regions whose growth meets trace and race as one), read the slope over 2 mm, and seed lines until they reach the red themselves -- coffee bean X-45 0 -> 8 curves (held 1305 -> 2674 mm2), on its side X90 10 -> 30 curves with the Auto fill 40 -> 21 walls, and Full keeps them; a second race after the unticked one, so ticking changes nothing where no wall bends

2026-10-17 20:33:56 -05:00

scale.js

scale: review fixes -- the field applies on Enter or blur only (no spin buttons, no arrow-key steps: each was a whole reload), the floor is 10 % (below it a fine mesh's vertices merge in the 1 um weld), the factor is rounded to the 2 decimals shown, and a rescale drops the import note's 'restored N supports' (they went with the reload)

2026-10-17 21:09:43 -05:00

solids.js

refactor: kissEnds moves to web/kiss.js (reach and widths as arguments) and loftExtrude to solids.js, so the sway braces can share them; output identical

2026-10-03 15:14:03 -05:00

step.js

import: load the STEP kernel while the user picks a file, cache it a year

2026-09-24 16:15:26 -05:00

stepworker.js

import: load the STEP kernel while the user picks a file, cache it a year

2026-09-24 16:15:26 -05:00

stl.js

stl: review fixes -- bytes after the last triangle still read as binary, keywords any case, solid_name headers

2026-09-30 14:33:13 -05:00

style.css

ui: Remove model -- a button in the stats card takes the part off the plate and brings back the start page, so the next model needs no reload; the drawn walls, removed fins, load arrow, Suggest list, section cut, scale, import note and undo go with it, the fin settings stay

2026-10-18 09:23:30 -05:00

suggestworker.js

suggest: rank in a Worker with the page's tunables -- a 250k-face figure froze the page for 14.5 s; now the longest frame is 17 ms and the ranking is the same, default or changed gap; inline when no Worker can run

2026-10-14 21:32:24 -05:00

sway.js

Allow optional Sway depth beyond the existing 60 mm cap (#241)

2026-10-13 07:38:43 -05:00

threemf.js

3mf: review fixes -- a coloured part's material table and the first slicer part no longer share resource id 5 (the slicer parts start past it), and the bed shift counts the slicer parts so a modifier reaching past the part stays on the bed; pinned with the interface crest on, which all three slicers still read as one two-part supports object

2026-10-14 21:25:19 -05:00

zip.js

3mf: open a 3MF

2026-09-22 09:00:52 +02:00