0 Fork 0

mirror of https://github.com/Klipper4FlashForge/firmware.git synced 2026-10-22 05:12:16 -05:00

Files

T

Oleksandr ShyshatskyiandClaude Opus 5 a6098c7f64 The README was the manual. It is a front door now, and the manual is nine pages.

Fourteen sections, install through troubleshooting, in the one file that
existed when there was nowhere else to put them. The site gave the manual a
home; this moves it there and orders it by what the reader is doing rather
than by which subsystem owns the answer. Someone whose printer will not boot
should not have to know that the symptom table lives in a file called
hardware-testing.md.

Three topics were documented two and three times over, and each copy was free
to drift: install in README and toolchange.md, calibration in README,
calibration.md and toolchange.md, slicer setup in README and toolchange.md,
"before you start" in all three. Each is now in one place.

The owner path is Is this for you -> Installing -> After the flash -> Your
first print -> Nozzle-offset calibration -> Printing -> Upgrading -> When
something goes wrong, with error codes, versions and how-it-works behind a
Reference group. The README keeps what a front door keeps: what this is, the
status checkboxes, what you give up, which file to download, and where to go
next.

toolchange.md was four documents in one 38 KB file. The owner half -- slicer
setup, filament, runout, the offset check before a first print -- is in
Printing and Your first print; the design notes, input shaper, roadmap,
HelixScreen and reverse-engineering notes stay, and the page moves to
Internals. hardware-testing.md was split down the middle by audience the same
way: the go/no-go checks and the symptom table were the owner's, and only
keeping the two verification files honest as the macros change is ours.

Two things this fixes rather than moves. The error-code table was
notes/70-error-codes.md, an internals note the README sent owners to; it is
docs/error-codes.md now, a page. And toolchange.md still opened "Not yet run
on hardware" while the README's checkboxes described a Creator 5 Pro that has
been printing for weeks -- the two pages have disagreed since the first
hardware run.

Contributors are deferred, as agreed: those pages are regrouped, not
rewritten. The nav says so.

Co-Authored-By: Claude Opus 5 (1M context) <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01S3XZh4SqPdXAowVndz6tMr

2026-08-28 22:20:19 +03:00

2.7 KiB

Raw Blame History

Error code table (English strings, complete)

Useful as a behavioral spec — every hardware fault the stock system distinguishes.

Toolchanger

E0127–E0130: T1–T4 not in dock. Cannot pick up extruder.
E0051–E0054: T1–T4 pickup failed.
E0131–E0134: T1–T4 already in dock. Cannot release extruder.
E0135–E0138: T1–T4 release failed.
E0139: Extruder mount sensor not triggered
E0140: Extruder dock sensor not triggered
E0141: Extruder mount sensor still triggered
E0142: Extruder dock sensor still triggered
E0143: State error after extruder pickup
E0144: State error after extruder release
E0145: Lock motor current abnormal
E0146: Unlock sensor not triggered.
E0160: Cannot release extruder. Homing failed.
E0165: extruder not installed, can not print.

Leveling / probe (eddy)

E0041: Leveling sensor cannot reset.
E0147: Build plate not removed. Please check.
E0148: The leveling extreme values are out of range. Please clean the platform or adjust its flatness, then try again.
E0149: Sensor not triggered at max travel.
E0150: Homing timeout.
E0151: Eddy current probe triggered before move.
E0152: During leveling, the values measured multiple times are out of range. Please clean the platform and nozzle, then try again.
E0153: During nozzle offset calibration, the values measured multiple times are out of range. Please clean the eddy-current sensor and nozzle, then try again.
E0161: Bed eddy current position abnormal. Please check.
E0167/E0168: The platform is not installed. Please install it and try again.

Heating

E0063–E0066: Extruder 1–4 heating error.
E0123: Bed heating error.
E0077: Chamber heating error.
E0154: Drive motor temp abnormal. Please check if PCB fan is on.

Axes / homing

E0012/E0013/E0014: X/Y/Z-axis signal not triggered.
E0155/E0156/E0157: X/Y/Z-axis limit still triggered after retract.
E0158: Sensor error. E0159: Homing error.

Communication

E0002: MCU communication lost.
E0124: Extruder mount MCU communication lost. (eboard)
E0125: Heater board MCU communication lost. (eheaterboard)
E0126: Leveling board MCU communication lost. (levelboard)
E0170–E0173: Lost communication with main/extruder/heater/level mcu
E0005: Printer is not ready. Please check if the wiring is correct.

Print-time

E0162: Paused. Filament runout.
E0163: Paused. Clog detected.
E0164: Paused. Spaghetti detected. (camera AI)
E0166: Print file error. E0169: Printer model mismatch. Please re-slice.
E0175: Internal error on command. E0176: The gcode move out of range.
E0021: Cannot open camera. / Camera not recognized.
E0174: Copy log error. E0999: Unknown error.

2.7 KiB Raw Blame History Unescape Escape